OUR SERVICES

TOOTH JEWELLERY

Ask us about our dental technologies to learn more about what’s available to you.

Tooth Jewellery

Content / Inhalt

  • 5 X Skyce* Crystal ø 1.9mm
  • 5 X Skyce* Sapphire blue / Saphir-blau ø 1.9mm
  • 5 X Skyce* Crystal ø 2.4mm
  • 5 X Skyce* Sapphire blue / Saphir-blau ø 2.4mm
    • 2 X Skyce* Crystal ø 2.4mm
    • 1 X Skyce* Sapphire blue / Saphir-blau ø 2.4mm
    • 2 X Skyce* Sapphire blue / Saphir-blau ø 1.9mm

  • Tooth Jewellery

  • Zahnschmuck
  • Bijou Dentaire
  • Gioiello da dente
  • Joyas orales
  • jóias bucais
  • Tandsmycken
  • Tandsmykke
  • Hammasjalokivet
  • Tannsmykke
  • TandversieringKoo

Instructions for Use

Description

Skyce is a range of crystal glass tooth jewellery. The stones are bonded to the labial surfaces of natural upper anterior teeth without invasive preparation.

Color and Sizes

Skyce is available in two sizes:

  • 1.9mm in diameter
  • 2.4mm in diameter

Color

  • transparent

Step by Step Application

  1. A rubber dam must be placed to avoid the aspiration or swallowing of the tooth jewellery.
  2. The contact surface of the tooth must be professionally cleaned with brushes or cups and polishing paste, eg. Proxyt
  3. A 37% phosphoric acid gel (eg Total Etch) is applied to the contact surface. The diameter of the etched surface must be slightly larger than that of the stone.
  4.  After 60s of etching, thoroughly rinse off the phosphoric acid with water.
  5. Carefully dry the tooth surface.
  6. Apply a thin coat of Heliobond or Tetric EvoFlow onto the etched region.
  7. Apply Heliobond or Tetric EvoFlow to the clean reverse side of Skyce and place the stone on the tooth surface. Some Heliobond or Tetric EvoFlow must come out along the sides of the stone to provide a setting for the stone.

Recommendation

In order to optimize the bond, fully coat the stone with the thin layer of Heliobond. This does not impair the lustre of the stone.

Important

Setting the tooth jewellery with  Heliobond and Tetric EvoFlow.

  1. The jewel must be light cured for at least 40s both from the labial and palatal aspects (eg with bluephase®).
  2. If, in rare cases, excess has to be removed,only use silicone polishers. Rotary instructions must not touch the stone to prevent scratching.

Note

  1. It is easier to apply Skyce if it is held with a probe to which soft wax or a bit of adhesive material from the tip of a OptraStick has been applied.
  2. Do not touch the stone with your fingers or allow it to become contaminated with saliva. If  Skyce is contaminated carefully clean the stone with acrylic pellets in an alcohol bath.
  3. For information about the side effects and interactions of the cementation materials and the phosphoric acid gel as well as any warnings, see the corresponding instructions for use.

Keep Out of the reach of Children.
For use in Dentistry only.

Date information prepared: 04/2008
Rev. 2
Ivoclar Vivadent AG
FL-9494 Schaan/Liechtenstein

The materials have been developed solely for use in dentistry. Processing should be carried out strictly according to the instructions for use. Liability cannot be accepted for damage resulting from failure to observe the instructions or  the stipulated area of application. The user is responsible for testing the material for its suitability and use  for any purpose not explicitly stated in the instructions. Descriptions and data constitute no warranty of attributes and are not binding.